Lorenz
metal detecting systems are some of the most sensitive and stable metal
detecting devices of their kind currently available and they are
designed primarily for professional search and location purposes.
The LORENZ DEEPMAX X3 is the result of many years of research and
development and is one of the newest developments in the field of Pulse
GBS metal detectors.
The
LORENZ DEEPMAX X3 is designed to be used with either small or large
coils. With frame coils it is possible to detect very effectively over
large areas to considerable depth. In addition small coils can be used
when searching for small metal objects. By enlarging the search coil
very high detection ranges can be achieved. Therefore search frames
with up to 3m square are available.
The Pulse GBS
(Pulse Ground Balancing System) is suitable for searching at depth and
specially designed electronics cancel out signals from the ground. The
LORENZ DEEPMAX X3 is therefore a reliable tool to locate metal objects
even with extreme soil and environmental conditions. A new improved
circuit design suppresses a range of interference from power lines or
radio transmitters and a power pulse technique produces very accurate
signals to obtain considerable detection depths.
The
LORENZ DEEPMAX X3 works with two different ground cancel filters. It
has an extended depth capability for non ferrous metal objects and it
is capable of identifying metal objects employing the two different
target identifications.
The Pulse Ground
Balancing System GBS performs well because of the time delay between
the transmitting and receiving phase. The high transmitting power is a
fundamental advantage and makes operation with very large search coils
possible. Because of its active working principle a high sensitivity
range for both ferrous- and non- ferrous metal objects is achieved.
The LORENZ DEEPMAX X3 was developed to provide a number of features
including high sensitivity and stability along with easy operation.
Simple operation with a minimum of controls and a large display make
the LORENZ DEEPMAX X3 a user friendly electronics device.
It
only takes a few moments to set the electronics to the prevailing
ground conditions. Basalt soil and bricks present no problems. The
selection of the ground filters one, two or three, in conjunction with
the adjustment of the corresponding controls Ground one and Ground two,
virtually cancels out unwanted signals. Even though the ground signal
could be a few hundred or thousand times stronger than the signal of a
small metal object, the LORENZ DEEPMAX X3 in-built technic accommodates
this and only produces a signal when metal is present. This is a
considerable plus over many other systems and the small reduction in
sensitivity is of little practical significance.
The
time delay function gives additional information on the probable kind
of metal located. The time delay of the eddy currents, produced in
conducting metal objects, is measured and indicated with a number
between zero and ninety nine. Three different ranges of metal objects
can be indicated namely: small non ferrous, ferrous and large non
ferrous metal objects.
When an induction balanced double D coil is
fitted, the LORENZ DEEPMAX X3 offers a sophisticated and refined
ferrous / non- ferrous target analysis on difficult soils and the
results are displayed using two different icons. Both the intensity bar
graph and the audio signal increase as the search coil comes nearer to
a metal object.
The LORENZ DEEPMAX X3 is made for use worldwide and a wide range of accessories are available to meet customer detection needs.
To suit different search and location purposes a variety of search coils can be connected to the LORENZ DEEPMAX X3.
Small search coils ranging from 26 to 45cm are held by a single person
with a telescopic pole. Frame coils range from 1m square to 3m square
and can be made of cable coils and plastic pipes or are readily
available from the manufacturer of the LORENZ DEEPMAX X3.
Very simple search frames can be made of inexpensive plastic water
pipes for example. The frame must be metal free and the cable coil
should be mounted on the surface of the frame.
The LORENZ
DEEPMAX X3 has a good range of functions and can therefore be used for
many search and location purposes. The DVD along with the booklet and
the suggested practical exercises help the operator make the most of
the detector in the field. Any organization that requires accurate
detection and location information will benefit from the performance of
the LORENZ DEEPMAX X3 when combined with optional GPS and data
collection systems. Extensive multi channel data collection can be made
with data collection techniques readily available from various
manufacturers. Optional multi sensor detection with GPS and software is
possible with several DEEPMAX X3 detectors working at the same time
like a scanner. The multi sensor trigger unit makes sure that every
detector and search coil works the same way with no interference
generated by nearby search coils. With suitable soft- and hardware
colour maps can be generated for example. Lorenz Detecting Systems
provide tailor-made detection equipment and various accessories to meet
customer needs e.g. detection of unexploded ordnance, meteorites, lost
aircraft, underwater or underground search applications.
The
DEEPMAX metal detectors combine modern technological developments with
a high quality product for professional metal detecting equipment.
We, as a design and manufacturing company, strive to maintain the
highest standards for our products and, therefore, alterations of the
design, specifications as well as the availability are subject to
change without notice. |
